What are the Differences between 4 Cycle and 2 Cycle Weed Eater?

how different between 4 cycle and 2 cycle weed eater

Gas-powered weed eaters deliver powerful performances to assist you to tackle tough, tall weeds on your lawn. When looking to buy one for your homecare or professional weed trimming needs, you have two options to choose from and these are the 2 and 4-cycle gas engines.
While these engines are aimed at providing the torque to power the trimmer though grass and lawn weed, each of them is unique. They have different characteristics, pros, and cons. While both are gas powered, the manner in which the fuel is converted into power is what sets them apart.
Deciding whether to go for the 2 or 4-cycle gas engines when buying a weed eater is often a perplexing one. Could one be better than the other? How are they different? What are the pros and cons of owning either of them? By going through today’s post, you will be able to pick up all this information and much more.

how different between 4 cycle and 2 cycle weed eater

How Do They Work?

The term cycles or stroke refers to the movement of the engine pistons inside the cylinder, end to end. It is these engine movements that generate the power transmitted to the trimmer heads. Essentially, the number of strokes that an engine makes to complete a power cycle is what gives the engine either a 4 or 2-cycle names. 

  • 4-Cycle Engines

From the description, a 4 cycle engine makes 4 strokes to produce a single power stroke. All the fours engine piston movements occur sequentially from the first to last. When you assume an engine that is upright, with its plug on top, then here is the sequence of operations. 

The first stroke is the downstroke where the engine piston moves downwards as the inlet valve lets in a mixture of air and gas into the cylinder. The second stage starts as soon as the piston reaches the bottom-most part of the cylinder. Inlet valve closes as the crankshaft forces the piston back up. 

Stage three (exhaust), which is the upstroke, occurs as the piston is pushed up. All valves close, resulting in the compression of the air-gas mixture. Once at the top, the spark plug ignites the mixture, resulting in an explosion that sends the piston back down. 

Stage four is another compression stroke as the piston rises up. In the course of the rise, exhaust valves open to allow the discharge of exhaust gases from the engine. A new cycle starts as soon as the piston reaches up. 

In a 4-cycle engine, there are two complete revolutions of the engine crankshaft to complete all the 4 strokes. The closing and opening of the inlet and exhaust valves are coordinated by gears driven by the crankshaft. 

Pros

  • Efficient combustion
  • Produces more torque
  • Low emission levels
  • No mixing of fuel and oil

Cons

  • Harder to start
  • Heavy
  • More parts to maintain
  • High vibration levels
  • Has to be kept level in storage
  • Requires regular oil changes
  • 2-Cycle Engines

Unlike a 4-cycle engine that generates power after the fourth stroke, a 2-cycle is more conservative. The power is output after every second piston stroke. These two stages combine the functionality of the above four. 

The first stroke combines the downward movement (power stroke) and exhaust (up) stroke. On the other hand, the second cycle combines compression and intake. The first two occur at the top of the cylinder, while the last two occur and the bottom. A single crankshaft revolution is facilitating the whole process. 

It is the sparking of the plug and the subsequent air-fuel mixture ignition that triggers the strokes. At some point during the downward movement, the piston passes the exhaust hole, allowing for the loss of some of the expanding gases. 

Further down, the piston opens the intake hole (located on the opposite side of the exhaust hole). Air and fuel mixture makes entry into the upper combustion chamber and then is forced into the upper part of the cylinder as the piston is pushed down by the combusting mixture. 

During the downstroke, the air intake from the carburettor is closed by a valve. In the following upward stroke, the valve opens to let in fuel-air mix into the cylinder. 

At the down most position, the crankshaft cams push the piston back up for the second cycle. Intake and exhaust holes are closed, trapping in some air and gas inside the upper part of the cylinder. The mixture gets compressed, and once it’s at the upper part, the spark plug ignites the mixture, resulting in combustion that shoves the piston down for the second time. 

As you can see, the lower end of the cylinder always has a mixture of air and fuel and not oil. Therefore, this engine requires the fuel to be mixed with the gas in a specified ration. The oil component lubricates the moving parts such as the cylinder, crankshaft, cylinder, and piston. 

how different between 4 cycle and 2 cycle weed eater

Pros

  • A small number of moving parts
  • Easy to maintain
  • Requires less storage space
  • Low vibration levels
  • Easy to start
  • Weighs less

Cons

  • Less torque
  • More emissions for the burning of oil
  • Mixing of oil and fuel is a hassle

How to Distinguish Between a 4 And 2-Cycle Internal Combustion Engine

After establishing the difference in how these two engines work, then you need to be able to distinguish between the engines just from first looks. I have studied both engines for quite a while now and have developed these criteria for distinguishing between the two. 

  1. Listen to the sound produced by the engine as it runs. This may be a layman’s way of identification, but it does work at times. A 4-stroke engine runs smoothly with no sound fluctuations. As for the 2-cycle, the engine is renowned for a loud crackling sound as it runs. 
  2. A 4-cycle engine has a separate oil reservoir. If you spot an oil cap, then it’s a 4-stroke. There is none on a 2-cycle since oil is mixed with the fuel.
  3. For the same weed eater specifications, a 4-cycle engine is considerably heavier than a 2-cycle. 
  4. A 4-cycle produces less smoke when starting the engine in comparison to the 2-cycle with considerate amounts of smoke. 

Differences between 4 and 2-Cycle Engines

Apart from the working principles and oil fuel mixing, there are a couple of differences between a 4 and 2-cycle engine. 

1. Lubrication Principles

In a 2-cycle engine, you have to mix oil and fuel in differing ratios. These often range from a single part of oil to about 50 gasoline parts or 1 part of oil to 20 gasoline parts. These ratios are indicated on the engine label. 

The reason why you must mix the two is due to the contact between crank, piston, cylinder and the fuel mixture. In a 4-stroke engine, this contact is eliminated. Instead, a different lubrication system is put in place with an oil reservoir within the crankcase. This oil requires topping and replacement after a period of running hours. 

2. Weight to Power Ratio

Another difference is in the amount of power generated by the two engines in comparison to their weights. First, 2-cycle engines are lighter than their 4-cycle counterparts. Therefore, the latter produces more power from their relatively lighter engines. 

A 2-cycle packs more horsepower at higher speeds since a complete power stroke only requires a single crankshaft revolution. More horsepower is then produced at high revolutions per minute. Also, this power has no significant decrease when cutting through dense grass growths. 

However, a 4-cycle engine with low power and speed output delivers more torque. This turning force is what allows you to cut through tough grass with ease. For heavy-duty uses, a 4-cycle guarantees better efficiency. 

3. Fuel Economy

This is another area where the 4-cycle engine outperforms their 2-cycle competitors. In the 4 strokes, the engine has a stage for individual air delivery, and discharge of exhaust gases. As a result, the engine uses less fuel and combusts most of the fuel. 

The major flaw in a 2-cycle engine is that the exhaust gases are never eliminated entirely from the combustion chamber before the inlet of a fresh mix of fuel, oil, and air. Part of this exhaust is ignited, while some of the fresh mixture introduced is let out during the discharge of exhaust fumes. This mixture does not do any work in the first place but exits the engine.

4, Amount of Noise Produced

Typically, a 4-cycle is quieter than a 2-cycle engine. The reason for this difference is the dedication of a third stroke for the function of ignition as well as combustion. During this phase, both inlet and outlet valves are closed, completely sealing the cylinders. 

As it enters the fourth cycle, most of the fuel has already burnt. Thus, as the exhaust gases exit the chamber, little noise filters out. Note that the noise is not completely non-existent, but it is not as pronounced as in the case of a 2-cycle engine. 

The design is a little different in a 2-cycle engine. Every down stroke is accompanied by combustion, which still goes on even as the exhaust gas exits the chamber. Usually, when the air-fuel mixture is ignited, a mini-explosion occurs which filters out as the exhaust gases is discharged. Noise levels depend on how large the engine is and the volume of the air-fuel mixture. 

5. Weed Eater Costs

A 2-cycle engine has a simpler design with fewer moving parts, which explains the relatively low prices in comparison to a 4-stroke engine. Any equipment powered by a 4-cycle engine is more expensive than a 2-cycle one, and not only for weed eaters. Therefore, if you are on a budget, then you are better off with a 2-cycle weed eater. 

6. Maintenance Requirements

While 4-cycle engines do not require oil to be mixed into their gases, 2-cycles do. If you do not get the ratio right, the engine might develop mechanical problems. However, with the availability of pre-mixed fuels, you do not worry about this eventuality. 

A 4-cycle has lots of complex moving parts. These many items increase the likelihood of something breaking. The cost of repair and maintenance frequencies is also higher than in a 2-cycle engine. 

7. Impacts On the Environment

Both engine types run on gas, which still leads to emissions that have an impact on the environment. Nevertheless, between the two, a 4-cycle is the lesser evil since it is more fuel efficient and quiet in comparison to a 2-cycle. 

Then, there is also the issue of oil being burnt in the latter type of engines, further worsening the environmental impact. So, if you are an environmentalist, then an electric weed eater is probably your only option. 

Bottom Line

After noting the differences between these two weed eater types, a fundamental question arises over which of the two is better. Each of them has their pros and cons, but owning a 2-cycle weed eater provides you better value for your money than the other option. 

For the most part, 2-cycle weed eaters reign supreme as they are reliable, easy to use, start, and require fewer maintenance costs. Alternatively, if your key consideration is the amount of torque output, then I recommend sticking to a 4-cycle weed eater. 

Nonetheless, stronger environmental regulations being drafted may doom your 2-cycle options. Because of their high environmental impacts, these stricter emission guidelines may soon face them out; unless the manufacturers make the technology used better or improve on the weaknesses of the 4-cycle engines. 

The Advantages of an Electric Weed Eater

the advantages of an electric weed eater

Trimming forms an integral part of your lawn care routine. If you have a lawn mower, certain parts of the lawn are left uncut. These include around fence posts, lawn furniture, and the edges of the gardens on the lawn. 

A weed trimmer is the best tool for working around these places. Some brands give you more capabilities than others when it comes to the flexibility of the trimmer head. Today, numerous models of trimmers are in existence. This makes it hard for buyers to settle on an option. 

A common dilemma faced by buyers is whether to buy an electric or a gas powered weed eater. Although a gas powered weed eater guarantees more power, an electric weed eater provides other conveniences. For homeowners who haven’t decided on what weed eater to buy, here are the advantages of an electric weed eater that may just make your mind up. 

Types of Electric Weed Eaters

Electric trimmers are categorized into two: corded and cordless weed eaters. While the former requires an electric cable to function while plugged in, the latter option only requires a charged battery to run. 

These two types offer different conveniences. A corded option is lightweight, powerful, but is restricted regarding total reach by the length of the cable. On the other hand, a cordless trimmer can be used anywhere, provided you have the battery charged. Of course, the charge duration is a drawback, but with modern lithium-ion batteries, you get an extended runtime. 

Even though both types are limited regarding the size of lawn you have, they still offer plenty of reasons for you to buy one. Let’s take a look at these advantages. 

the advantage of an electric weed eater

What Can You Do with an Electric Weed Wacker?

Weed eaters are not for only taming the unruly grass and weed in your backyard. There are a host of other applications for which  electric weed eaters are well suited for. These include:

  • They can be used to chop thorny vines into minute pieces
  • Small bushes and shrubs can be trimmed at an instance with a powerful electric weed eater
  • The trimmer head converts to a handy lawn edger by turning it through 900. In this way, it turns into a great tool for applying the finishing touches to your cement paths, driveways, and lawn edges. 
  • Holding the trimmer head flat on a heap of leaves and then holding it in place turns the tool into the perfect leaf mulcher.

The Advantages of an Electric Weed Eater

1.Low Weight

If there is one reason why most homeowners are turning to electric weed eaters, then it has something to do with their lightweight nature. An electric weed whacker weighs much less than a gas option. At first, it may seem insignificant until you start working on your lawn. 

Holding a tool weighing more than 15 pounds in your arms for about an hour is not an easy task. It leaves you achy and sore. Also, if you consider other factors, then you would see the essence of having a weed eater weighing around 10 pounds or less. 

By virtue of their low weight, these tools are easy to maneuver on the lawn. You can, therefore, perform intricate lawn mowing patterns, just as you like it. In addition, you can work for longer hours without feeling fatigued. 

the advantages of an electric weed eater

2.Echo-Friendly

Perhaps the most noticeable advantage of electric weed eaters is their friendliness to the planet. If you are a champion for making the planet greener, then this choice would be great for you. Unlike gas powered weed eaters, electric weed whackers do not emit any fumes into the environment. 

Because of stringent emissions laws being put in place in light of increased global warming, weed eaters that use gasoline are not allowed to be used in certain jurisdictions. When you are in such a place like California, then you are better off with an electric weed eater.

Emissions are not only good for the environment. They are potentially harmful to your health as well. 

3.Easy to Start and Operate

Warming up, mixing up of fuel, and persistent pulling on the chord are maneuvers not liked by a lot of users. You want a tool that you can start using as soon as possible. When you have an electric weed eater, you do not have to undergo all these troubles to get it up and running. 

All an electric whacker needs is a push of a button, and it starts. After you have completed your trimming, simply press the stop button. An instant start-stop allows you to get to work and stop as soon as possible quickly. The latter feature helps to alleviate the risk of injury. 

Another key convenience feature is that you don’t have to stop for refills in case of a corded electric trimmer. However, if you have a cordless model, then you have to stop for recharging when power runs out. 

4.Minimal Noise Levels

For their powerful nature, gas-powered electric weed eaters have one notable flaw. They are extremely noisy. While modern weed eater engineering has considerably reduced how noisy they are, the noise is still a problem. 

On the other hand, an electric weed eater runs so quietly that you may not need to have an earplug on as you work. That being said, you still have to practice safe weed eater operation which requires you to have earplugs. 

Because of the relatively low noise levels, you can work on your lawn at odd hours without drawing the wrath of your neighbors. You should note that they are not noiseless as there is still considerable sound emitted from the motor and moving parts. 

5.Little to No Maintenance Requirement

Maintenance work on any tool is never anyone’s cup of tea, especially when getting oil spilt on you. With an electric weed eater, there is little maintenance work to be done, if any. The same cannot be said of a gas weed whacker that needs tuning and routine maintenance procedures. 

Other than retracting the electric cord, recharging and replacing the battery for cordless types, the only maintenance job required on an electric weed whacker is cleaning it after use. The grass debris that sticks onto the trimmer head should be cleared before storing, waiting for the next use. 

In addition to cleaning, a string trimmer needs the string spool replaced regularly when it runs out. This process is often very easy, requiring a couple of minutes and you’re done. 

6.You Can Opt to Free Yourself from Cords

Since electric weed eaters come in two options, you have the choice of having the cordless one. Using a battery gives you the freedom of taking your tool to any working location of your choice without being constrained by the power cord. 

In other instances, people have ended up cutting the cord as they trim or embarrassingly tripping on it. A cordless weed eater does not run out of cable giving you the ability to work on even the farthest corners of your lawn. 

7.No Oil Mixing

2-cycle gas powered engines have a knack for wearing down users with their requirement for mixing oil and gas in certain ratios. It is common to have maybe a bit too much oil or gas unless you buy a pre-mixed fuel-oil solution. In this way, you don’t have to deal with the ratio problem.

An electric option on the other hand, requires none of that. All you need is the battery, a charging station, power outlet or a power cord for a corded trimmer. 

8.Decently Powered

Concerns about electric weed eaters have been about their apparent less powerful nature. Yes, that used to be true in the past, but with current battery technology, their performances have been vastly improved. 

More powerful lithium-ion battery tends to rival the performance delivery by gasoline-powered weed trimmers. Battery powered weed eaters are capable of lasting longer, tackling thicker grass, and charge faster than before. Corded motors are also more powerful, yet lighter than they used to be a couple of years back. 

9.Batteries Can Be Shared with Other Yard Tools

Everybody appreciates the universality of power tools. It is a great cost-saving move, as you only have to buy a single battery for some tools. Once you are through with trimming but still have some charge left in the battery, then you can use the same battery to power your chainsaw. This is what universal design of lawn equipment is all about. 

It is not only a chainsaw that you can share the batteries with. Other lawn care tools include a blower, power tool among a host of others. Of late, there are even lawn mowers that use the same batteries as a weed eater. 

Conclusion

The truth is that an electric weed eater is an excellent lawn care equipment. Despite its inefficiency at times, it has advantages that more than makes up for their drawbacks. 

I hope that these advantages have shed more light into electric weed whackers to help you make the decision whether to get one or not. Apart from the features, a person’s preference also comes into play when buying a lawn care equipment. 

What Type of Fuel is Suitable for Your Weed Eater?

Weed eaters are powered differently. Some are powered using batteries, others using electricity and the rest using gasoline. Weed eaters powered using gasoline come in two types of engines, which are the four cycle engines and two cycle engines. 

Whichever type of engine you are using, you need to use the appropriate type of fuel in your weed eater. This is because using the right type of fuel aids in increasing the life of your engine. Read on and get to learn more regarding what type of fuel is suitable for your weed eater. 

Right and Wrong Fuel for your Weed Eater

Ensure you have the right fuel before you pour it into your weed eater. You should look out for the components of the fuel for your gasoline powered weed eater. The alcohol content of the gasoline should not exceed 10%. Completely keep off diesel fuel and instead strictly stick to ethanol-free gasoline. 

The ultimate fuel for your weed eater should be fresh, unleaded and clean 87-octane. To ease the task of looking for the ultimate fuel for your weed eater, the manufacturer normally indicates the type of fuel that should be used with your weed eater. This is because it differs from the brand to brand. 

Getting the best weed eater should be your first concern since the rest comes easy after you have acquired a weed eater from a reliable manufacturer. If by any chance you do not find the fuel recommended by the manufacturer, premium weed eater oil will be perfect for your air cooled engine. 

Do not result to using automotive oil or boat engine oil since either of these fuels will ruin the engine of your weed eater. Automotive oil and boat engine oil are not formulated appropriately. 

How to Acquire the Right Mixture Ratio

For the users of the two cycle engine, buying the right type of fuel is not the end of your work. You also need to ensure that you use the right amount of it together with gasoline. Adding in too much fuel is dangerous since it is likely to cause damage to the engine to the extent that it may knock and crack. 

Too little oil on the other hand will cause the weed eater engine to produce oily and heavy smoke. For this reason, you need to know how to mix fuel for your weed eater. The normal fuel, oil ratio is 40:1. To acquire the appropriate mixture ration, add fluid which is 3.2 ounce bottle of oil to a gallon of gasoline. 

If you need a bigger quantity, add to 2.5 gallons of gasoline an 8-fluid ounce bottle of oil. Before pouring in the fuel and oil into the engine, mix them appropriately in a container. Close the container in which you are making the mixture tightly then shake it several time to allow the mixture to blend. 

Shake the container with the mixture first every time you refill the trimmer. Shaking the container will ensure that the oil and gas are blended appropriately. It is wrong to pour them into the engine separately since they will get mix up all by themselves. 

In an instance where you discover that the ratio of the mixture is wrong, you need to turn the weed eater off to prevent it from getting ruined. To remedy the situation, simply empty the tank and ensure that you get the ratio of the fuel and oil right before you restart the engine.

How do you know if the oil fuel ratio is improper? 

To know that the ratio of oil and fuel is improper, you will not have to carry out numerous tests. The engine does show clear signs that something is wrong either by producing too much smoke if the oil in the mixture is too much. If the gasoline levels are too high, the engine makes cracking sounds and becomes extremely hot. 

What Type of Fuel is Suitable for Your Weed Eater

Proper Storage of the Weed Eater

To store your weed eater for a longer period of time, you need to store it in the right way and under the right conditions. Ensure that you empty the fuel tank to store your weed eater safely for a period of over a month. 

Make sure that you have completely emptied the tank by replacing the cap and starting the trimmer. Let the trimmer run for some time till it ceases to clear out the fuel which could be remaining. 

If gasoline is stored in the fuel tank for long, it becomes gummy hence blocking the system. Gasoline will also certainly corrode the inner part of the fuel tank which will cause more problems later on as you try to start your machine. 

What type of fuel is suitable with your weed eater

Important Tips to Consider

  • A fuel mixer that is well over three months old could lead to starting problems. 
  • If too much smoke or heat comes from the engine, it shows that the fuel mixture is improperly blended, wrong or old. 
  • Gasoline with an alcohol percentage that exceeds 10% is dangerous since it can cause the engine’s power to drain off or run erratically. If using gasoline with an alcohol percentage of more than 10%, I would recommend that you drain off the fuel tank every time after you use it. 
  • Even though fuel stabilizers come in handy in some engines, they are not appropriate for weed eaters since fuel has oil. 

Conclusion

When it comes to the question of what type of fuel is suitable for your weed eater, there is no justification for taking chances. Ensure that you observe the manufacturer’s instructions in the manual regarding the right fuel for your weed eater. Also, when mixing up the fuel to oil ratio, make sure that you observe the 40:1 ratio to ensure that the engine of your machine does not experience any mishaps as you work. 

One key point you need to observe is that once you are done with your day’s work, you should get rid of the unused fuel from the weed eater, start the engine and run it dry. With that, it will be safe for storage. Following these key points will ensure that you have a happy and responsive weed eater for your engine. 

I hope that the article was helpful and that you will have it easy determining what type of fuel is best for your weed eater. Where you need clarification on matters regarding the ultimate fuel for your weed eater, feel free to ask and I will be glad to offer my assistance as soon as I can. 

Do you want to know when you should respool a weed Eater?

A weed eater is a handy tool for a homeowner. It is useful in trimming weeds and grass in tight spaces or around obstacles which incapacitates a lawnmower. Despite all the differences regarding designs and modes of powering, the working principles of a lawn mower and a weed eater remain the same. 

Every weed eater uses a fast spinning string of plastic string to whack grass around your lawn. The trimming line is withdrawn from a spool, mostly by bumping the trimmer head on the ground. After a while, the spool runs out and you have to respool the weed eater.  But do you know exactly when you should respool a weed eater?

The task of respooling can also be done for a variant of reasons and not necessarily when the spool is empty. Sadly, it is one that not many people do not love doing or wait too long before undertaking. Knowing when to respool a weed eater is essential in retaining its effectiveness.

do you want to know when you should respool a weed eater

When Should You Respool Your Weed Eater?

Frankly speaking, there are a number of reasons why you need to respool your weed eater. The first and main reason is usually when the line has run out. When you have been whacking the weeds in your backyard for some time then no line advances, this may mean that the line could have run out.

Your weed whacker trimming line, usually made of some kind of plastic, wears down as you use it. The resulting repeated high-speed contact with weed, pavements, fence posts, trees, grass, and stones renders the working line section ineffective after a while. 

At that point, you then have to advance a newer portion of the line by bumping the weed eater head on the ground by relying on the automatic option. 

It does not matter whether you are using either an automatic or bump feed string line. Another way of telling that the line is at its end is to check for a change in trimming quality. If it deteriorates, then it means only a small portion of the line remains in the spool.

In other instances, it could be as a result of problems with the line itself. If the spooling were done poorly in the first place, then it wouldn’t trim as you would want. Twists in the line would necessitate a change of spool for a better one. 

There is no set time or moment when you should respool a weed eater. If you suspect any issues with your line, then you need to stop working and check it out. It could even be a case of a line that keeps on getting stuck. In case you are out of line, or the current line is ineffective, then it’s time to replace the spool. 

How to Respool Your Weed Eater

After you have established that you indeed need a new line, it is time for you to install a new spool into the trimmer head. With this little help from me, you can actually do it yourself and stop relying on help. 

The process is a standard one, whether you have a battery powered, electric or a gas powered trimmer. Respooling the weed eater can be done in two ways. First, you can re-string the line onto the spool yourself, often from a bulk of line. Secondly, you can also buy an already would spool and insert it into the spool slot. The latter saves you time but will cost you more. 

What you need

  • Bulk trimmer string line
  • A pair of scissors
  • Measuring tape
  • Washcloth
  • Pre-wound spool (this is optional)

1. Buy the right string size

If you check the manual your string trimmer came with, you will notice a specification on the thickness of string it should use. The diameter is usually dependent on the type of power. More powerful gas trimmers take the thicker strings, with diameters ranging from 0.80” to 0.11”.

The less powerful battery powered and electric trimmers use the thinner 0.065 strings. A thicker string than the recommended will not fit through the hole. Conversely, a thin string underutilizes a trimmer meant for thick strings. 

2. Disconnect the source of power

Safety procedures require that your trimmer has to be switched off before you can start using it. For electric and battery powered tools, unplug or remove its battery before you can disassemble its trimmer head. The last thing you want is to have the tool switching on while in use. 

Also, ensure the trimmer cools down completely before attempting any works on it. A hot gearbox and trimmer head could cause you burns. 

3. Disassemble the Trimmer Head

Have the trimmer lay flat on a workbench or work table. Others find it easier to hold it upside down so that you can easily access the trimmer head. Once in a position you are comfortable with, remove the trimmer head’s retainer cap. 

This process involves unscrewing the cap, pressing on a tab then turning the cap in an anticlockwise direction, or a method specified by the manufacturer. All in all, it should be an intuitive process of turning the head in the indicated direction, then pulling outwards. 

4. Clean the Housing of the Spool

Once you have opened the trimmer head, pull out any remaining string line inside. Then use the washcloth to tidy up the housing of the spool. Repeated use creates a buildup of stones and grass inside the housing that reduces the ease of unwinding of the spool. 

5. Measure Out the Required Length of Spool

If you check either on the manual or the spool housing, you will notice a specification on the length of trimming string the spool can accommodate. Use the measuring tape to determine the exact length as you draw out the bulk length of the string. 

For spools that accommodate 30 feet of string, measure this and then cut off the line. Allow for allowances of a couple of inches. This step is only required if you intend to re-string the spool yourself. Otherwise, you would have just inserted the pre-strung pool right back in and covered the head.

6. Wind The String onto The Spool

Note that if your weed eater uses two strings, then you have to measure the two specified string lengths. Once you have the length you need, locate a center hole on the housing, then push through about ½ inch of line. This length holds the string in place as you wind it. 

For a two-stringed weed eater, each housing section has its center hole, with a divider in between. Work with one section then go to the next. Check the indicated direction of wrapping, and then wind the line side by side, layer by layer. Do the same to the other side. 

7. Clip The Ends into The Notches

Do not wind the whole length of the string. Leave about 5-6 inches unwound. On the edge of the spool(s) is a notch. Clip the protruding end into this notch (will be two in a double stringed trimmer). These notches aid in keeping the line in place as you put back the spool. 

8. Return the Spool Housing

Assemble back the spool housing into the trimmer head hub. Release the string end you had clipped in the spool notch. Pass the end through the line exit hole (eyelets) located on the weed eater head. This step should be repeated for the second spool whenever applicable. 

9. Re-Attach the Trimmer Retainer Cap

After replacing the spool into the weed whacker head, align the spool retainer with the eyelet slot. Try to pull the string through to see it unwind smoothly. If it does, screw back or snap the retainer ring into place. 

Try to wiggle the ring a little for a tight fit. It might fly as soon as you start the trimmer off if it is left loose. Put back everything together, then power back your tool and continue with your work.

Tips to Ensure You Don’t Respool Too Often

The frequency with which you respool a weed eater depends to a great extent on how you use it. The more torture you subject your line to then the time duration when you should respool a weed eater becomes shorter. 

  • Use a trimmer line guard to protect it from hitting other objects such as fence posts, lawn furniture or house sidings. These objects wear out a trimming at a faster rate. Otherwise, the line might damage the likes of house sidings.
  • For a dense weed growth, start the trimming process at the top of the weeds, working your way downwards. Starting down subjects the string to excessive strain.

do you want to know when you should respool a weedeater

  • Avoid thick patches of twigs, vines or grass.
  • Only use the string trimmer when the grass is slightly dry, but not too wet. Wet grass is heavy, and quickly wears your strings. 
  • Use personal protective equipment when using the string trimmer. It doesn’t prolong the lifespan of the string, but it keeps you from harm’s way.

Conclusion

There is no specific time when you should respool a weed eater. It all depends on several factors such as the intensity of the weed growth, the line thickness and how many hard surfaces it comes into contact with. The respooling process is easy too that you can comfortably do yourself in just a couple of minutes. 

How do you Take Care of Your Lawn When You Are on a Vacation?

How do you take care of your lawn when you are on a vacation

Everyone deserves a refreshing rest after a series of hectic months at work. Summer then becomes the perfect time for you and your family to have a good time before the kids return to school. July and August is that time of the year to put most of the things on hold.

As you head off to your well-deserved summer vacation, whether for days, weeks or months, you still have concerns about your beloved lawn. When you’re gone, the lawn still grows and this means it has to be attended to.

However, finding a willing neighbor or relative to help you out might be unattainable at times. There are still ways in which you can keep the lawn watered, nourished, and well-kept even in your absence.

These tips on how to take care of your lawn when you are on vacation will help ensure that you come back to your usual lavish lawn. 

What is the Safest Way to Use a Weedeater?

What is the safest way to use a weedeater

Initially, you need to be familiarized what weedeater machines are.   Weedeaters are portable lawn care power tools also known as string trimmers, weed wackers or simply whackers. These equipment devices are used in trimming and edging your lawn and other similar land structure with a grassy condition. They do not use blades to cut grass but use flexible monofilament line similar to a fishing line only thicker.

The following topics will guide you on how to be safe starting with your PPE or Personal Protective Equipment. Next to it is the step by step safety guidelines alongside with the weedeater’s uses and functions.

Start with Your Personal Protective Equipment

Eye Protection

Wear safety glasses that are certified to withstand shattering in severe cases and will surely protect your eyes from debris everywhere. There are also safety glasses with side shields designed to be worn over your prescription glasses. Make sure to replace safety glasses when they become filled with scratches or become brittle.

Face Shields

Face shields are recommended if the grass area is heavy and flying debris is expected probably due to wind or effect from trimming on open areas. Safety glasses sometimes become insufficient and a backup cover is needed. 

Dust Masks

Wear high-quality dust masks suitable to the task you are about to perform and when exposed to concentrations of dust and/or airborne debris. Do not wear the mask when it is already worn out or damaged as it will compromise its ultimate purpose in deterring the dust particles and other elements.

Hearing Protection

Depending on the type of machine you are going to use, always make sure your ears are also protected. Extended exposure to noise can result in hearing problems. Use earplugs or earmuffs in these work environments.

Hand Protection

Use work gloves with the proper thickness or rubberized linings appropriate to the machine being used and based on your hand’s sensitivity.

Work Shoes

Tough and closed shoes are required. You might be working on areas that have potential hazards, especially when you are moving the objects away from your work areas. Work shoes appropriate for the type of work being done are needed. Open-toed shoes or sandals are not safe to use. You might need to wear boots or long socks to cover your entire feet and legs from crawling insects in the area of work.

Hard Hats

Hardhats are needed and ideal for every construction type of work. Grass trimming may include moving large objects and you need to have a projection from possible head injury or falling objects & debris. You may also include an absorbent fabric head band to keep the perspiration from running over your face.

Safety Vests

Safety vests will make sure that people can notice you while you are using tools that may cause hazards to them, especially if there are several individuals working with you. Wear safety vests or high-visibility clothing in your work area.

Step by Step Safety Procedure

  • Gear up and wear all necessary Personal Protective Equipment (PPE). Tie up if you have long hair or use a hat and hairnet and make sure to keep it away from the engine or motor of the weedeater.
  • It is safer to let the grass and weeds dry out before trimming. Grasses are lighter when they are dry.
  • Hold the trimmer right and tight with both hands. Make sure it is on the right side of your body so that the muffler and smoke is away from your face. Keep your left arm straight and allow your right arm slightly bent and flexible.
  • Stand upright and place the trimmer at the same level of your waist. Start and move slowly, initially to feel the force of the machine while keeping your position steady and firm. Do the cutting from right to left while keeping the debris away from you.
  • Continue cutting from top to bottom especially if the grasses are long and thick. The motor will not be stressed out and so as your arms and legs.
  • Slowly tap your trimmer’s bump knob to the level ground to release more line to avoid engine stalling. Allow the tip of the line do the trimming and not the middle part. It is most effective using the line tip. When the string breaks down or gets damaged, just run the machine at a high speed and slowly bump its knob to the ground to release an extra trimming line.
  • The trimmer line might get damaged if it hits anything hard like walls and metal objects. So make sure to hit the grass and weeds only. If it hits hard objects, stop the machine and double check your line trimmer for potential problems.
  • Cutting around the trees, fences and posts are more challenging since you do not want to damage any of these including you trimmer. So rotate your trimmer to a 90-degree angle from the ground to make a more precise trimming. Do not use string trimmers to cut grass against the trunk of trees. Doing so might kill the tree if the monofilament line cuts the bark of the tree.

Safely Conclude Your Task

Before you head on and begin with your trimming task, applying precautionary measures is a must. It may seem like a common backyard or outdoor chore on a daily basis, but using a weedeater to edge your lawn and cut the growing turfs down still require an utmost preparation to prevent any accidents and any damages to your equipment.

To sum it all up, here are the important reminders you should take note of:

  • Regularly inspect your PPE (Personal Protective Equipment) for optimum safety conditions to make sure you are getting the right benefits from those shields.
  • Safely disengaged your weedeater or trimmer and carefully place it away from individuals especially children that might bump onto them and cause accidents or even damage to the equipment.
  • Always leave your workplace clean and neat and free from potential hazards to passersby and co-workers.

There is nothing can compare to having the job done completely and safely if you follow the steps and precautions discussed herein.

Should You Establish a Lawn Care Business? Here’s All You Need to Know

Should You Establish A Lawn Care Business

Putting up a business is a tough field to go through. There are a lot of factors to consider before you settle down in a business venture that would bring in a reasonable financial gain. You have to make investments in equipment and other materials you need to start out a business before getting all the profit back to your savings. Although there are no certain outputs, sometimes you need to take a risky step to know how it will turn out.

If you are planning to establish a lawn care business, will it be worth to try? It is probably hard to tell but you won’t know unless you do it. It takes a lot of careful planning and saving before you get to the peak of success. Proper evaluation of your financial ability, the equipment to use, the market you should capture, and an effective advertisement is highly imperative.

How to Cut Grass Without a Weed Eater

how to cut grass without a weed eater

When the turf on your lawn starts to grow taller, it may require some trimming and edging. You need to use the right gardening equipment to cut them efficiently. Weed eaters are known to be one of the reliable tools you can use to keep your lawn neat and clean and even when those weeds grow near the fence or building. However, there might be circumstances where it is not possible to use a weed eater to cut and edge the grass on your lawn.

Your equipment is probably not functional and completely broken or you really just don’t have enough budget to invest in a weed eater. Whatever the reason is, you may find it a little challenging to cut the turf on your lawn without the proper gardening tool.

Other Ways to Cut Grass Without a Weed Eater

When a weed eater is not possible to use, there are many alternative ways that are efficient to cut the grass on your lawn. You may even find these gardening tools in your garage or at the back of your yard!

how to cut grass without a weed eater1. Use a sickle or scythe.

Even before weed eaters and other automatic mowers become widely available, a sickle or scythe has been among the traditional ways of mowing a lawn. It comes with a long handle known as a snath or snaith which is usually made of wood but some modern types can now be made of metal. It also consists of a curved sharp steel blade which becomes the tool’s main trimmer and edger.

Cutting the grass with a scythe becomes efficient if you’re doing it in a correct position and proper swings. When the grass is 2 feet tall or much higher than that, make sure you are standing in a comfortable position when holding the handle. You may need some force from the muscles on your hips and thighs when you swing the scythe to cut the grass on the lawn. Swing the tool back and forth.

You can move to the next area of your lawn once you’re done cutting with one part. If you want a neat, fast, and clean trimming and edging, the cutting edge of the tool should be parallel to the ground, according to Home Guides.

2. Use a round-point spade shovel.

Another popular gardening tool you can use is a shovel. They come in different sizes and shapes so opt for the round-point spade. Though it is commonly used for digging up the ground, it is also a good alternative for mowing your lawn. However, you can’t just start digging in the areas where trimming is needed. If you don’t do it the proper way, you will end up with a patchy or uneven lawn.

If you want to set up a clear area where you want to start trimming, you will need 2 wooden sticks and a string. Set up two sticks according to the distance you prefer, then tie up a string from one stick to another. Putting up a line on your lawn will make your mowing work neater and much easier to do.

As you have put up a clear area, use the round-point spade shovel and place it along the edge of the line. Press down the shovel two inches onto the ground using your foot to clear up the grass along the line. Cut the grass and remove it. Once you are done with the area, you can move the line you’ve set up, and place it in the next area. You can start digging and cutting until you’ve finished the whole area. This can be a little messy because of the dirt and soil. To clean up the lawn, you can also use the shovel.

3. Use lawn shears.

Using lawn or garden shears is as easy as using a pair of scissors, only these are heavier and larger. Back then when gardeners and owners wanted to make a few trims on their lawn, they have always had their shears to do the job. Even today, a lot of homeowners opt for this gardening tool to cut and edge the grass on their lawn, especially the taller ones.

The trimming work also becomes much neater and easier to do if you clearly know where to start. You can move across the yard slowly until you’ve reached the other side. You may also want to start cutting the grass in the small areas. Just make sure that your shears are fully sharpened and the handle provides a good grip. So, even when you move and cut the grass from one place to another, it won’t cause so much trouble. Cutting the grass would be easy as a breeze.

There are lawn shears that have long handles that allow you to conveniently cut the grass while you are in a standing position. Some types, however, have shorter handles where you have to lean closer to the ground to do the trimming. Nonetheless, these shears are an effective tool to help you cut the grass on your lawn.

4. Try using a lawn mower.

This is an ideal option for those who have large lawns. With such enormous size of a lawn, it definitely requires a powerful and functional gardening equipment to maintain it. Shears, shovel, and scythe would also be helpful at some point. But if you want to make the grass cutting much faster to do, you can try a lawn mower.

There are factors, however, you have to consider first before using a lawn mower. You have to check your lawn first and clear it up whenever there are rocks, sticks, or debris that might get stuck in the mower and they might damage the blades, too. It is also important to check the height of the grass before you proceed on cutting. If the grass is too tall for the mower, it is better to make a few trims using the tools mentioned before.

If you want to know whether the grass is too tall for the mower or not, you can measure it using a measuring tape or if you know its height but just looking at it, that would be fine. You should also check your mower’s manual and check its deck height. The average deck height is 4 inches while some mowers can go up to 6 inches. If you proceed on cutting the tall grass without determining the deck height or the grass height, it may cause damage to your turf and your mower as well.

It is better to mow the grass when it is dry. If it is wet or damp, it may result in larger grass clippings which can block up the mower. It can really be messy as well. After mowing, irrigate the lawn for better moisture. However, it is not advisable to water the lawn late in the afternoon or the evening as fungal problems may arise. Mowing early in the morning and watering the lawn right away after cutting is the best way.

Choose the Right Cutting Tools

how to cut grass without a weed eater

Using a weed eater makes the grass cutting efficient, fast, and easy. You can choose among gas powered, battery powered or electric weed eater to do all the trimming and edging work on your lawn. However, there could be instances where it is not possible for a homeowner or gardener to use such equipment. But there is good news; there is certainly a lot of reliable gardening tools that you can use as an alternative to a weed eater.

If you are looking for an alternative, it is essential to use the right cutting tools for mowing and maintaining your lawn. Scythe or sickle, lawn shears, round-point shovel, and lawn mowers are some of the gardening tools you can try using whenever a weed eater is not available. But before you proceed on using these tools, there are guidelines you have to follow in order to get the desired results.

Conclusion

You can wait until your weed eater is completely repaired or when you have enough budget to get one. For the meantime, there are efficient and useful gardening tools you can use to clear up your lawn, cut the grass, keep it neat, and hence, make it a healthier place for your pets and family.

When Will You Need a New Weed Eater?

When you have a yard, it is necessary to provide regular maintenance. You need to cut those weeds off and make a few trims on the grass to keep your yard clean and healthy. Gardeners and homeowners may find this task a little difficult without the right gardening equipment. But since weed eaters have become widely available in the market, yard maintenance won’t be much of a problem anymore.

Although a weed eater can get the job done in your yard or garden, the equipment itself also requires regular maintenance. Unfortunately, many owners don’t have enough time to do this. That’s why the equipment just wears out until it’s no longer useful.

Should you get a new equipment right away, then? How will you know when to get a new weed eater?

Why You Need a Weed Eater

Before you decide whether to get a new weed eater or not, you’ve got to know first why you need to use this equipment for your yard, lawn, or garden. It will help you understand the importance of using a weed eater in its utmost condition.

Weed eaters are available in different types. You can choose among electric, battery-powered, and gas-powered weed eaters. Although they vary in some ways, like the noise, power output, engine performance, and the range or distance they can cover, they all function to keep your yard, lawn, or garden neatly trimmed.

If your equipment is properly maintained or in its best condition, you surely will benefit from these positive results:

  • It is much easier to clean and trim all the weeds in your lawn, garden, or yard. It does all the trimming job for you and gets it done in no time.
  • You don’t need to be a professional to do the trimming. Weed eaters allow you to cut those weeds and grass off according to the length you prefer.
  • It comes with a long handle that allows you to do the maintenance without straining your arms and back.
  • This gardening equipment enables you to work faster thus gives you more time for your other duties and household chores.
  • You can maintain a healthy, green, and clean environment for your family.

When will you need a new weedeater

Signs You Need a New Weed Eater

When your weed eater gets damaged and seems malfunctioning, it will give you more headache than getting the gardening task done. It might also take so much of your time before you finish all the trimming you need.

Some owners, however, still want to stick with their equipment, provide some repairs, and use it as long as it is working. If you feel the same way or seem uncertain whether to get a new weed eater for your gardening duties, you must determine the damages that might affect your equipment’s performance. You may also consider some factors.

When will you need a new weed eater? Take a look at these signs.

1. When the weed eater is not starting.

There are a lot of possible causes why the weed eater is not starting. It can be due to a blocked fuel filter, dirty air filter, or it has just totally worn out. If you are using an electric weed eater, make sure that it is plugged into an electric outlet. But if it’s plugged and still does not power up, there might be a problem with the cord or the spark plug.

Gas-powered weed eaters, on the other hand, require fuel in the tank. If there isn’t enough fuel, it may not really start. The same thing goes with battery-operated weed eaters. They may be convenient to use as they are cordless, but replacement of batteries from time to time is necessary.

Considering all these situations, it can actually be resolved with quick and easy ways. However, if your weed eater is not starting despite having it plugged, fueled, or powered up with batteries, there must be a more serious damage in its engine. This needs to be checked. If repairs are not possible, you need to replace your weed eater with a new one.

2. When it is not cutting the grass.

The ultimate solution you’d probably think of is to restring the weed eater or buy a replacement for the string cartridge. If you know how to do it yourself, it might not cost as much as when you have it repaired. But if not, then you might need to spend a little to change the string.

The common reason why the weed eater is not doing its trimming job is when the string comes out. Then, as what was mentioned, you have to restring the weed eater. But if you’ve done this step and the weed eater is still not cutting the grass, it might require some repairs which may cost a lot.

3. When you see obvious damages on the equipment.

When most of its parts are damaged and broken, it may be working but it may not be safe to use. Eventually, it will break and won’t be working anymore. If that happens, you should consider getting a new weed eater.

4. When it is totally worn out.

When it looks like a total trash, malfunctioning, damaged and broken, then you have to give it up! There are weed eater brands that are durable and reliable for a long time. But due to certain conditions, improper use, lack of maintenance, and extensive use, a weed eater can wear out eventually. And sometimes, all you have to do is keep it in the garage or throw it away!

5. When you have acquired a bigger lawn or yard.

Bigger and wider space requires additional gardening equipment. And if you’ve expanded your territory or acquired a bigger lawn, yard, or garden, a new weed eater might come in handy. An additional equipment might cost you some bucks but it can be very useful in the long run.

When will you need a new weed eater

Conclusion

A lot of users consider extensive repairs and replacement of the parts to keep their weed eater in the best condition. Although this might be a good option, it would be better to think carefully if it is really worth the money. Many have been skeptical whether to get a new weed eater or not because of the price tag. But some repairs and replacements cost as much as the brand new weed eater.

So, if you’re looking for a high-quality weed eater with superior performance, why don’t you consider getting a new one? And if you’ve noticed any of the signs mentioned, then it’s probably time to give up your old equipment.

Is It Dangerous When You Use a Weed Eater near the Fence or Building?

Fenced houses, buildings, and establishments with a lawn or yard require some trimming every now and then. Lawn mowers are an efficient equipment to keep those green fields neat and clean. But if you want to get into the corners of the fences and around the buildings and posts, a lawn mower might be too bulky and big. Hence, a weed eater is what you need.

A weed eater is an innovative gardening equipment that provides precise trimming and edging. It helps maintain your lawn and keep it in a much neater and cleaner condition. However, since this is the most appropriate equipment to reach the spaces and corners along the fences, buildings, and other establishments, some users expressed their concerns whether it is dangerous or not to get too close to those areas.

Can a weed eater damage your fence or the areas near the building? Is it really dangerous? How can you use a weed eater safely?

Is it Really Dangerous?

Is it dangerous when use the weedeater near the fence or building

Just like any other gardening equipment, improper use can cause damage to your lawn and fences. So, if you use the weed eater the wrong way, it might not really be safe to use. Although this can be a factor, the fences, the bottom part of the building or the post itself can also be vulnerable to damages if they are not regularly maintained. There are some effective procedures that you can try to protect and fortify your fences and the areas around your establishment.

Metal posts and flashing are some of the recommended materials that you can use to reinforce your fences in the yard. Keeping them regularly maintained and durable will allow you to use the weed eater more efficiently. Although a weed eater is lightweight and ergonomically engineered with slimmer parts to reach the innermost areas, you still have got to be extra careful when using it.

When it comes to trimming the lawn near the building, it won’t be a problem if you prefer using a weed eater. You can trim the weeds in the areas near the building but do not try to get too close to the building or establishment. The utmost concern isn’t the damages that you can cause to the building, but rather the damages your weed eater could get.

Unlike fences, buildings are concrete would not likely easily get damaged by a weed eater. Some scratches might be visible or the paint might flake overtime if you often trim the weeds too close to the building.

Then so, is it dangerous to use a weed eater near the building or fence? No, it won’t be if you apply the proper precaution and handling. If you trim within these areas and not get too close to the fence or building, using a weed eater won’t be a problem. But if you handle and use it improperly, it can really be dangerous.

How to Safely Use a Weed Eater

Is it dangerous when you use the weedeater near the fence or building

Whatever type of weed eater you use, perhaps a gas-powered weed eater, cordless or battery-powered, and electric, there are safety protocols you have to follow to prevent damages on the establishments, fences, and to your equipment as well.

Here are some tips you can keep in mind before and while using a weed eater.

  • Always wear safety goggles before using this gardening equipment.
  • Use ear muffs or earplugs for ear protection, especially when you are using a gas-powered weed eater. This type is really loud and can definitely sound unpleasant to your ears.
  • Always check the strings. Make sure that you don’t have more string than you need. Do not let the strings go out hanging on both sides of the head. If you have longer than you need, it can cause your engine to overwork and will drop its horsepower. Thus, it won’t provide a precise cut or whatever cut you want. The motor won’t function correctly and might not work at all eventually.
  • Before making a cut, you need a good balance when handling the equipment.
  • When you are using the equipment, you should lay the head flat and keep it that way all the time to prevent weed eater burn. Don’t push it down too far on the ground. If you’re tilting or using it in an angle, it will lead to weed eater burn. This causes the weeds to grow in different lengths or and different areas.
  • Always do the weed eating after mowing. So, that you can gauge your height to what you’re trimming. It will also prevent uneven edges.
  • Once you place the head on the ground flat, keep up with a steady motion from one side to another. Walk forward nicely and slowly. Keep the head flat at all times.
  • If there are any rocks on the lawn, set them all aside first. If you run your equipment over them, your nylon might break.
  • If you are cutting along the fence, you’ve got to be careful. You can go near it but not too close. There might be times that you may need to touch the fence to trim all the weeds off. But don’t drag it all the way to the fence. You might damage both the fence and your equipment.

Conclusion

Keeping your lawn regularly trimmed provides you a healthier space and environment. However, if you’re going to use a weed eater along the fence or near the building, there are safety measures you have to apply first to prevent damages on the establishment and to your equipment.

It seems dangerous to use a weed eater near the fence or the building, but actually, it isn’t. As long as you know how to use the weed eater properly and reinforce your fences and posts around the building with a better support and material, trimming those weeds won’t be a problem at all.